0%

Table of Contents

EUROMAP Global Plastics Flow Study: Only 12% of the World's Plastic Waste Is Actually Recycled

EUROMAP's Global Plastics Flow Study 2023 was released in October 2025 and covers 45 countries representing 81% of global GDP. It is essentially a full-lifecycle material flow analysis, tracking plastics from raw material production through conversion, consumption, waste generation, collection, recycling, incineration, landfill and leakage into the environment. The core findings are summarised below.

Table 1 — Global plastics flows, 2023

表格

IndicatorVolume
Annual plastics production414 million tonnes
Fossil-based share of production374 million tonnes
Plastic products entering the market407 million tonnes
Post-consumer plastic waste generated300 million tonnes
Waste managed in an environmentally sound way212 million tonnes (71%) — landfill 97 Mt, incineration with energy recovery 64 Mt, collected for recycling 51 Mt
Waste mismanaged87 million tonnes (29%)
Recyclate actually produced37 million tonnes
Actual (output-based) recycling rate12%
Recyclate as a share of annual plastics output9%

I. Global headline figures

1. ProductionGlobal plastics production stands at 414 million tonnes a year, of which 374 million tonnes is fossil-based. Some 407 million tonnes of plastic products enter the market. Output has risen steadily over the five years since 2018, when production was 370 million tonnes, driven by higher per-capita plastics consumption.

2. Waste generationA total of 300 million tonnes of post-consumer plastic waste is generated each year (the study counts only waste arising after consumer use; industrial scrap is excluded).

3. Where the 300 million tonnes goes71% (212 million tonnes) is managed in an environmentally sound way:

  • Controlled sanitary landfill: 97 million tonnes
  • Incineration with energy recovery: 64 million tonnes
  • Collected and sorted for recycling: 51 million tonnes

The remaining 29% (87 million tonnes) is mismanaged — open dumping, uncontrolled burning and littering — with part of it eventually leaking into soil, rivers and oceans.

4. Real recycling efficiencyAlthough 51 million tonnes is taken in by recyclers, sorting, contaminant removal and processing losses mean that only 37 million tonnes is actually converted into recycled material. The global actual recycling rate is therefore just 12%, and recyclate accounts for only 9% of total plastics output in the year.

In short: only about one-tenth of the world's plastic waste ends up as new plastic; most is landfilled or incinerated.

II. Regional differences

1. EuropeWaste: 50.1 million tonnes. Environmentally sound management rate: 88%, the highest in the world. Actual recycling rate: 27%. Recycling systems within the EU are mature, but littering and open burning in Turkey and non-EU Eastern European countries are significant and drag down the regional average. Europe also still exports plastic waste to countries with weaker waste governance.

2. Asia (including China)Waste: 148.2 million tonnes, the largest volume of any region. Environmentally sound management rate: 69%. Total collected for recycling: 28.4 million tonnes, the highest in the world, yet the recycling rate is only 19%. Sorting technology varies widely, informal recycling workshops are widespread and processing losses are relatively high. China is the core source of Asia's recycling volume.

3. North AmericaWaste: 46.1 million tonnes. Environmentally sound management rate: 96%, but achieved mainly through landfill; the recycling share is very low, reflecting weaker household recycling habits.

4. AfricaWaste infrastructure is severely lacking. Per-capita mismanaged waste is the highest in the world, and open dumping and open burning are the most acute. Many areas have no proper landfill sites.

5. Latin AmericaThe pattern is close to North America: landfill dominates, incineration capacity is insufficient, and recycling is at a moderate level.

III. Patterns by end-use sector

1. Packaging is the main source of waste.Packaging plastics have the shortest service life and are discarded after use, so they account for the largest share of waste and are the main target for recycling (PE, PP and PET). Film-based plastics, however, carry heavy contamination and suffer very high recycling losses.

2. Construction, automotive and appliance plastics have long cycles.Plastics used in building materials and vehicles have service lives of 10–30 years. Plastic consumed in 2023 will not become waste that year; it will do so many years later. The consequence: production keeps rising now, and waste volumes will keep climbing for decades to come.

3. PVC and PS are hard to recycle.Additives limit the recycling of PVC, so it is more often incinerated or landfilled.

IV. What has changed since the 2018 baseline

  • 2018: 250 million tonnes of plastic waste, 63 million tonnes mismanaged, 14 million tonnes leaking into the environment, actual recycling rate of about 12–15%.
  • 2023: waste up to 300 million tonnes, the mismanaged share only slightly lower at 29% (from 30%), and the recycling rate barely improved.

The core problem: plastics production is growing faster than recycling systems are being built. Technology gaps and high recycling costs mean progress towards a circular economy remains slow.

V. Key judgments and policy recommendations

1. Structural problems differ by income level.In developed economies the main issues are weak recycling participation and heavy reliance on landfill; in developing economies they are inadequate waste collection infrastructure and the prevalence of informal recycling. Technology upgrades alone will not solve either problem.

2. Practical measures

  • Low-income countries should prioritise building waste collection systems.
  • Europe should strictly restrict plastic waste exports and stop shifting environmental pressure overseas.
  • Extended producer responsibility (EPR) should be implemented globally, making plastics producers bear the cost of recycling.
  • Investment in high-performance recycling technology should be increased to cut sorting losses, with the aim of lifting the recyclate share above 20%.

3. ConclusionWithout stronger, globally harmonised policy, the share of recycled plastic is unlikely to rise significantly for a long time.

VI. Limitations of the study

  1. Only post-consumer waste is counted; plastic scrap generated during manufacturing is outside the scope.
  2. Many smaller countries lack official statistics, so figures are modelled.
  3. Informal recycling (collection and sorting by small-scale operators) is estimated, so data for developing countries carries a reasonable margin of error.

Source: China Plastics Machinery (中国塑机), published via 86pla.com (Plastics Machinery Network) on 13 July 2026. Original article: EUROMAP 全球塑料流动研究报告内容摘要

Kevin Davis

Kevin Davis

Kevin Davis is a Product Development Specialist at Chengheng Plastic Machinery, with a focus on improving the automation features of our machines. Kevin leverages his expertise in electrical engineering and control systems to integrate the latest technologies into our product line. He’s been with Chengheng for 5 years and has played a key role in developing several new features for our film blowing and bag making machines. He's currently working on a project to improve the precision of our printing machine’s registration system. Kevin holds a Master’s degree from Purdue University.
Previous Trade Alert: Recent Anti-Dumping Actions Targeting Chinese Plastics and Related Products
Next From Code to Practice: A New Legal Starting Point for the Green Transition of Plastic Packaging